We Fix Bosch Solution 3000 Alarms....FAST

Book a Service call Online NOW
Instant Appointment Confirmation

$135.00 includes 30 minutes on site

Call an alarm expert
(03) 9005 0174

Or simply fill in the form and we’ll be in touch

Bosch-Solution-3000-codepad
Bosch_rsc_+_app

Is Your Bosch Solution 3000 Alarm System Faulty? Need Repairs?
We Can Help!

$135.00 includes the first 30 minutes - that's the lowest service rate in Melbourne!

.Our experienced technicians have been servicing security systems in Melbourne for over 30 years. We’ve seen and repaired every fault imaginable on Bosch security systems including the Solution 3000. That’s why we’re confident that we’ll have your fault repaired…properly … in 30 minutes.

When it comes to alarm system servicing and repairs you’re paying for a technician’s time. The more experienced the technician, the less time it will take to repair.

Steve is our senior tech -he has been serivng and repairng alarms since the 1980’s. No matter what problem you’re having with your alarm, Steve will fix it…..FAST!

Melbourne Alarms is a trusted family-owned business that was established in 1982 - see our reviews below

Looking For The Bosch Solution 3000 User Manual?

Looking For The Bosch Solution 3000 Programming Manual?

Why Choose Melbourne Alarms?

How Do I Stop My Bosch Alarm Beeping?

If a fault occurs, the FAULT or MAINS indicators flash and the codepad beeps once every minute
If the AC MAINS supply fails, the MAINS indicator flashes until the AC MAINS supply is
restored. Pressing the [#] or ‘AWAY’ button once acknowledges the fault and stops the codepad from
beeping once every min.

1. Hold down the [5] key until two beeps sound. The STAY and AWAY indicators flash in
unison. A zone indicator displays the type of fault that occurred (for example, Zone 1 =
System Fault). Refer to Fault Indicators, page 18 of the User guide for the list of possible system faults.
2. To further determine the type of fault condition, press the key that corresponds to the
zone indicator displayed. For example, if Zone 1 displayed System Fault, press the [1] key
to display which system fault occurred.
3. To exit Fault Analysis Mode and return to the disarmed state, press the [#] key. The
FAULT indicator continues to display and the codepad stops sounding once a min.
Fault Indicators
Zone Fault Description Press Zone Fault Condition
Indicator Button Indicator
1 System Fault 1

1 Battery Fail
2 Date and Time
3 RF Receiver Fail
4 Output 1 to 3 Fail
5 Telephone Line Fail
7 Power Supply Fail
8 Onboard Tamper
9 to 16 RF Repeaters 1 to 8 Fail (Solution
2000 N.A.)
2 RF Low Battery 

Press ‘2’ to display which zone has the low battery

3 Zone Tamper

Press ‘2’ to display which zone has a tamper alarm

4 Sensor Watch Fault 

5 RF Sensor Missing 

6 Communication Fail 

Press ‘6’ to get more info:

1 Receiver 1 Fail
2 Receiver 2 Fail
3 IP Module 1 Fail
4 IP Module 2 Fail

7 Output and Codepad Fail


The output fault registers when the output expander B308 is disconnected or tampered.
The codepad fault registers when any codepad is tampered or disconnected from the control
panel.
To determine which fault occurred, press the [7] key.


8 Keyfob Low Battery


This fault occurs when any of the RF keyfobs report a low battery condition to the control
panel. To determine which keyfob failed, press the [8] key. Only keyfob 1 to 16 faults display
on the codepad through zone indicator 1 to 16.

Adding a User Code

Adding User Codes
Only the Master Code holder can add or change other system user codes, including the Master
Code. Up to 32 user codes / radio user codes can be programmed to operate the system.
How to Add a User Code
1. Enter your Master Code, followed by [1] and the [#] button (for example, [25801#]).
Three beeps are heard and the STAY and AWAY indicators flash.
2. Enter the User Code number (1 to 32), followed by the [#] button (for example, [2#] =
User 2, [8#] = User 8). Two beeps are heard and the selected user number displays on
the codepad indicators.
3. Enter the digits required for the new code followed by the [#] button (for example, for
User Code 5768, enter [5768#]). Two beeps are heard and the STAY and AWAY indicators
turn off.
To add or change other User Codes, repeat this procedure as many times as required.

Programming Stay Mode 2 Automatic Bypass Zones

Programming STAY Mode 2 Bypass Zones 


Programming zones to be automatically isolated in STAY Mode 2 are only carried out if you
have a Master Code or Installer Code.
How to Program STAY Mode 2 Zones
1. Enter your Master Code or Installer Code, followed by [4] and the [#] button (for
example, followed [25804#]). Three beeps sound and the STAY indicator flashes.
2. Enter the zone number to be automatically isolated, followed by the [*] button (for
example, [1*] = Zone 1, [2*] = Zone 2). The selected zone flashes. If you make a mistake,
enter the same zone number followed by the [#] button to clear the incorrect zone. To
select additional zones to be automatically isolated in STAY Mode 2, repeat Step 2 as
many times as required.
3. Press the [#] button to exit this mode when you finish selecting all zones to be
automatically isolated in STAY Mode 2. Two beeps sound and the STAY and AWAY
indicators turn off.

Manually Isolating Zones

Isolating Zones on the Bosch Solution 3000


Use isolating zones to manually disable one or more zones before arming the system. Once a
zone is isolated, you can access that zone during the armed state without activating an alarm.
For example, you need to isolate a zone because before arming the system a PIR detector may
be false alarming, or you need to leave a pet inside a particular zone while away.
Isolating zones is performed by one of two methods. Method two is optional and only allows
those user codes programmed by your installer to have access to isolate zones.


Standard Isolating 
Standard isolating allows all operators to isolate zones without knowing a valid user code.


How to Isolate a Zone
1. Press the [*] button twice to enter the Isolating Mode. Three beeps are heard and the
STAY indicator flashes.
2. Enter the zone number (1 to 8 / 16), followed by the[*] button (for example, [1*] = Zone
1, [2*] = Zone 2). Each zone to be isolated has a corresponding zone indicator that
flashes. If you selected an incorrect zone to be isolated, enter the incorrect zone number
again followed by the [*] button. Repeat Step 2 if more than one zone is to be isolated
until all zones to be isolated are selected.
3. Press the [#] button after all selected zones are isolated. Two beeps are heard and the
system returns to the disarmed state.


Code to Isolate 
This method restricts only those User Codes with the Code to Isolate priority level to isolate
zones.
If any User Code has this priority level, the method of standard isolating does not function.


How to Isolate a Zone
1. Press the [*] button followed by your User Code and the [*] button again to enter the
Isolating Mode (for example, [*2580*]). Three beeps sound and the STAY indicator
flashes.
2. Enter the zone number (1 to 8 / 16), followed by the [*] button (for example, [1*] = Zone
1, [2*]= Zone 2). Each zone to be isolated has a corresponding zone indicator that
flashes. If you selected an incorrect zone to be isolated, enter the incorrect zone number
again followed by the[*] button. Repeat Step 2 if more than one zone is to be isolated
until all zones to be isolated are selected.

Change Time & Date

Programming the date and time is only required when you need functions such as automatic
test reports, automatic arming, and history events to operate correctly.
How to Program the Date and Time
1. Enter your Master Code, followed by [6] and the [#] key (for example, [25806#]). Three
beeps sound, and the STAY and AWAY indicators flash.
2. Enter the day, month, year, hour, and minute(DD, MM, YY, HH, MM format) (for example,
DD = day of the month, MM = month of the year, YY = current year, HH = hour of the day,
MM = minute of the day). To program the hour of the day, use the 24:00 hour format.
3. Press the [#] button to exit and return to the disarmed state. Two beeps sound, and the
STAY and AWAY indicators turn off. If a long beep sounds, an error was made when
entering the date and time.

Testing Your Bosch Security System

The following functions let you confirm that your Bosch Solution 3000 alarm system system is operating correctly:
Horn Speaker Test

Hold the [1] key until two beeps sound.
The horn speaker sounds for 2 sec.

Bell Test

Hold the [2] key until two beeps sound.
The bell output operates for 2 sec.

Strobe Test

1. Hold the [3] key until three beeps sound. The strobe flashes.
2. Hold the [3] key until two beeps sound. The strobe stops flashing.

Walk Test Mode

Use Walk Test Mode to test detection devices to ensure that they are operating correctly.
Every time you test a zone, the codepad sounds one long beep, and the horn speaker sounds
one short beep to indicate that the zone is activated when testing.
1. Enter your Master Code, followed by the [7] and [#] keys (for example, [25807#]). Three
beeps sound, and the STAY and AWAY indicators flash. The codepad beeps once every
sec while the system is in Walk Test Mode.
2. Activate all zones requiring the test.
3. When you finish testing all required zones, press the [#] key to exit from this mode. Two
beeps sound, and the STAY and AWAY indicators turn off. The system returns to the
disarmed state.

Alarm key pad was flashing the battery symbol intermittingly. Could not be happier with the service provided, from the lovely lady who took my call and to Steve arriving on time and explaining all that he would do. Battery replaced. I highly reccommend this company. The person who initially installed alarm system (different company) was so unreliable. Steve was just absolutely amazing, thank you so much.

Silvana Costanzo – Preston

Agree with previous reviews! Tara was courteous, professional, knowledgeable and informative. She repaired a faulty alarm that another serviceman had botched. Her instructions were very clear. I would highly recommend Melbourne Alarms and Tara to anyone looking to do a repair or install.

Chris – Kew

alarm-service-and-repairs-man

Lowest Service Call Price in Melbourne!

Consider Calling Us If...

Ready?
Let Melbourne's Most Experience Service Team Fix Your Alarm

Our family owned business has installed more than 9000 security systems in Melbourne since 1982

Highly recommend Melbourne Alarms & Monititoring for the fantastic job. Tara arrived at the designated time and walked me through the process of identifying the issue with my alarm system. She replaced the sensor in a timely manner and thoroughly tested the unit to ensure the problem had been resolved. Don’t look anywhere else this is a professional family run business.

Karen Murphy, Montmorency

Extremely happy with the service. Pay attention to details. Tara and Robbie are very professional.
I installed a PET friendly alarm system last year. The Bosch system works perfectly well for my little cat who loves running around the house at night. Definitely recommend!

Helen Minh-An Pham, Point Cook

We are security technicians not salesmen!

Upgrade your older alarm system to take advantage of the latest technology

Partial Upgrade

Full Upgrade

Alarm Systems Fixed...FAST

We service almost any type of system installed over the last 20 years no matter who installed it

 

Bosch Solution 3000 Self-Help Section

How Do I Stop My Bosch Alarm Beeping?

If a fault occurs, the FAULT or MAINS indicators flash and the codepad beeps once every minute
If the AC MAINS supply fails, the MAINS indicator flashes until the AC MAINS supply is
restored. Pressing the [#] or ‘AWAY’ button once acknowledges the fault and stops the codepad from
beeping once every min.

1. Hold down the [5] key until two beeps sound. The STAY and AWAY indicators flash in
unison. A zone indicator displays the type of fault that occurred (for example, Zone 1 =
System Fault). Refer to Fault Indicators, page 18 of the User guide for the list of possible system faults.
2. To further determine the type of fault condition, press the key that corresponds to the
zone indicator displayed. For example, if Zone 1 displayed System Fault, press the [1] key
to display which system fault occurred.
3. To exit Fault Analysis Mode and return to the disarmed state, press the [#] key. The
FAULT indicator continues to display and the codepad stops sounding once a min.
Fault Indicators
Zone Fault Description Press Zone Fault Condition
Indicator Button Indicator
1 System Fault 1

1 Battery Fail
2 Date and Time
3 RF Receiver Fail
4 Output 1 to 3 Fail
5 Telephone Line Fail
7 Power Supply Fail
8 Onboard Tamper
9 to 16 RF Repeaters 1 to 8 Fail (Solution
2000 N.A.)
2 RF Low Battery 

Press ‘2’ to display which zone has the low battery

3 Zone Tamper

Press ‘2’ to display which zone has a tamper alarm

4 Sensor Watch Fault 

5 RF Sensor Missing 

6 Communication Fail 

Press ‘6’ to get more info:

1 Receiver 1 Fail
2 Receiver 2 Fail
3 IP Module 1 Fail
4 IP Module 2 Fail

7 Output and Codepad Fail


The output fault registers when the output expander B308 is disconnected or tampered.
The codepad fault registers when any codepad is tampered or disconnected from the control
panel.
To determine which fault occurred, press the [7] key.


8 Keyfob Low Battery


This fault occurs when any of the RF keyfobs report a low battery condition to the control
panel. To determine which keyfob failed, press the [8] key. Only keyfob 1 to 16 faults display
on the codepad through zone indicator 1 to 16.

Adding a User Code

Adding User Codes
Only the Master Code holder can add or change other system user codes, including the Master
Code. Up to 32 user codes / radio user codes can be programmed to operate the system.
How to Add a User Code
1. Enter your Master Code, followed by [1] and the [#] button (for example, [25801#]).
Three beeps are heard and the STAY and AWAY indicators flash.
2. Enter the User Code number (1 to 32), followed by the [#] button (for example, [2#] =
User 2, [8#] = User 8). Two beeps are heard and the selected user number displays on
the codepad indicators.
3. Enter the digits required for the new code followed by the [#] button (for example, for
User Code 5768, enter [5768#]). Two beeps are heard and the STAY and AWAY indicators
turn off.
To add or change other User Codes, repeat this procedure as many times as required.

Programming Stay Mode 2 Automatic Bypass Zones

Programming STAY Mode 2 Bypass Zones 


Programming zones to be automatically isolated in STAY Mode 2 are only carried out if you
have a Master Code or Installer Code.
How to Program STAY Mode 2 Zones
1. Enter your Master Code or Installer Code, followed by [4] and the [#] button (for
example, followed [25804#]). Three beeps sound and the STAY indicator flashes.
2. Enter the zone number to be automatically isolated, followed by the [*] button (for
example, [1*] = Zone 1, [2*] = Zone 2). The selected zone flashes. If you make a mistake,
enter the same zone number followed by the [#] button to clear the incorrect zone. To
select additional zones to be automatically isolated in STAY Mode 2, repeat Step 2 as
many times as required.
3. Press the [#] button to exit this mode when you finish selecting all zones to be
automatically isolated in STAY Mode 2. Two beeps sound and the STAY and AWAY
indicators turn off.

Manually Isolating Zones

Isolating Zones on the Bosch Solution 3000


Use isolating zones to manually disable one or more zones before arming the system. Once a
zone is isolated, you can access that zone during the armed state without activating an alarm.
For example, you need to isolate a zone because before arming the system a PIR detector may
be false alarming, or you need to leave a pet inside a particular zone while away.
Isolating zones is performed by one of two methods. Method two is optional and only allows
those user codes programmed by your installer to have access to isolate zones.


Standard Isolating 
Standard isolating allows all operators to isolate zones without knowing a valid user code.


How to Isolate a Zone
1. Press the [*] button twice to enter the Isolating Mode. Three beeps are heard and the
STAY indicator flashes.
2. Enter the zone number (1 to 8 / 16), followed by the[*] button (for example, [1*] = Zone
1, [2*] = Zone 2). Each zone to be isolated has a corresponding zone indicator that
flashes. If you selected an incorrect zone to be isolated, enter the incorrect zone number
again followed by the [*] button. Repeat Step 2 if more than one zone is to be isolated
until all zones to be isolated are selected.
3. Press the [#] button after all selected zones are isolated. Two beeps are heard and the
system returns to the disarmed state.


Code to Isolate 
This method restricts only those User Codes with the Code to Isolate priority level to isolate
zones.
If any User Code has this priority level, the method of standard isolating does not function.


How to Isolate a Zone
1. Press the [*] button followed by your User Code and the [*] button again to enter the
Isolating Mode (for example, [*2580*]). Three beeps sound and the STAY indicator
flashes.
2. Enter the zone number (1 to 8 / 16), followed by the [*] button (for example, [1*] = Zone
1, [2*]= Zone 2). Each zone to be isolated has a corresponding zone indicator that
flashes. If you selected an incorrect zone to be isolated, enter the incorrect zone number
again followed by the[*] button. Repeat Step 2 if more than one zone is to be isolated
until all zones to be isolated are selected.

Change Time & Date

Programming the date and time is only required when you need functions such as automatic
test reports, automatic arming, and history events to operate correctly.
How to Program the Date and Time
1. Enter your Master Code, followed by [6] and the [#] key (for example, [25806#]). Three
beeps sound, and the STAY and AWAY indicators flash.
2. Enter the day, month, year, hour, and minute(DD, MM, YY, HH, MM format) (for example,
DD = day of the month, MM = month of the year, YY = current year, HH = hour of the day,
MM = minute of the day). To program the hour of the day, use the 24:00 hour format.
3. Press the [#] button to exit and return to the disarmed state. Two beeps sound, and the
STAY and AWAY indicators turn off. If a long beep sounds, an error was made when
entering the date and time.

Testing Your Bosch Security System

The following functions let you confirm that your Bosch Solution 3000 alarm system system is operating correctly:
Horn Speaker Test

Hold the [1] key until two beeps sound.
The horn speaker sounds for 2 sec.

Bell Test

Hold the [2] key until two beeps sound.
The bell output operates for 2 sec.

Strobe Test

1. Hold the [3] key until three beeps sound. The strobe flashes.
2. Hold the [3] key until two beeps sound. The strobe stops flashing.

Walk Test Mode

Use Walk Test Mode to test detection devices to ensure that they are operating correctly.
Every time you test a zone, the codepad sounds one long beep, and the horn speaker sounds
one short beep to indicate that the zone is activated when testing.
1. Enter your Master Code, followed by the [7] and [#] keys (for example, [25807#]). Three
beeps sound, and the STAY and AWAY indicators flash. The codepad beeps once every
sec while the system is in Walk Test Mode.
2. Activate all zones requiring the test.
3. When you finish testing all required zones, press the [#] key to exit from this mode. Two
beeps sound, and the STAY and AWAY indicators turn off. The system returns to the
disarmed state.

YouTube Video Library

Stop Your Bosch Alarm Beeping

Changing The Code on Bosch Solution 880, 2000, 3000

Changing The Code on Bosch Solution 6000

Replacing the back-up battery in your bosch alarm panel

Replacing the battery in your Bosch remote control

Replacing the battery in your Bosch wireless motion detector

Bosch RSC Plus app for Bosch Solution 2000 and 3000

Bosch My Alarm app for Bosch Solution 6000 

Changing the time and date on a Bosch Solution 6000 panel

If your system is false alarming, try this

Ready?
Let Melbourne's Most Experience Service Team Fix Your Alarm

Our family owned business has installed more than 9000 security systems in Melbourne since 1982

Alarm System Specials

from $897.00 incl installation.

CCTV Deals

$1,799 incl installation & GST

Alarm & CCTV System

$1,987.00 Incl installation & GST

Expert Service & Repairs

Hello Robyn,

Just wanted to say how delightful Tara was today. She is very knowledgable and helpful and it was a pleasure having her install the new system.

Thank You

Anna Chan, Kensington

Most professional company I have ever dealt with. The installation team 
Steve and Tara were exceptional in knowledge of product, fault finding,attention to client satisfaction , most courteous with clients,and really cleaned up after installation completed.No hesitation in recommending this company ,from initial phone call to Robbie who provided good advice and a very detailed quotation to completion of job.

Peter Redman, Elstenwick

Careful, tidy and professional!”

“Excellent service. Friendly, helpful and very efficient. I have every confidence in my new Melbourne Alarms security system.

Thanks, Steve”

– J. Tubbs , Melton

Thanks very much Steve. You have put into my home an excellent system. I now feel safe and secure.

J. Kantor, South Yarra

 

Excellent job. Solved all problems. A very careful installer – very neat. A first class job.

B. McGee, Malvern

Melbourne Alarms Expert Service & Repair of Your Alarm System

Our qualified and experiences service technician will promptly diagnose the fault

If the repair will take longer than 30 minutes we’ll let you know

If the problem is a bit more involved we’ll discuss the options with you in plain English and give you a written quotation

We aim to get your system working as quickly as possible

Other Services:

Pet Sensors

Got a new pet? Replace one or more Standard motion sensors with pet-tolerent sensors.

Add an App

Apps are available for most modern security systems. Arm, disarm and get alarm notifications on your smartphone

Garage Door Alert

Ever come home to find that your garage door was still open? Add a 'Garage Door Left Open ' alert to your system.

Remote Controls

Add the convenience of remote controls to your security system

Video Verification Camera

Add a camera that alerts you if your alarm has been triggered. Sends a video clip to your phone. Works with any system

Early Warning

Add early warning perimeter detection. Be alerted if a potential intruder is prowling around your vulnerable doors and windows. Take action while he’s still outside

Ready?
Let Melbourne's Most Experience Service Team Fix Your Alarm

Our family owned business has installed more than 9000 security systems in Melbourne since 1982

We Are Security Experts Not Salespeople

Pet Sensors

Got a new pet? Replace one or more Standard motion sensors with pet-tolerent sensors.

Add an App

Apps are available for most modern security systems. Arm, disarm and get alarm notifications on your smartphone

Garage Door Alert

Ever come home to find that your garage door was still open? Add a 'Garage Door Left Open ' alert to your system.

Remote Controls

Add the convenience of remote controls to your security system

Video Verification Camera

Add a camera that alerts you if your alarm has been triggered. Sends a video clip to your phone. Works with any system

Early Warning

Add early warning perimeter detection. Be alerted if a potential intruder is prowling around your vulnerable doors and windows. Take action while he’s still outside

Let's Find The Right Security Solution For Your Home

Speak with alarm experts, not sales people

(03) 9005-0174

Monday – Friday 09:00am – 4:00pm